My build has finally begun and in this post I will take you on the building journey. Make sure you have read part 1 here , part 2 here , part 3 here

Lifting it up in the shed

It’s been some time since my last update. The machine is complete, but it’s worth noting that I had to construct a shed specifically to accommodate it; the machine proved too large for the existing brick structure.

I bought a garage “engine block” crane to lift the approximately 350kg structure in the shed. You really notice that using the right tools in a situation likes this makes huge amount of difference.

Replication method at work

After moving and leveling the machine I had to make the surface of the aluminium extrusion flat in order to mount the rails to it.

It is a bit of a messy situation but hey! it works.

After making the surface flat I cut out the slot with a hot-knife in order to mount my rails to it.

Adjusting the gantry level

I used the metal epoxy “gap filling” method to level the gantry vs the Y1 and Y2 gantry rails:

I used Mirror glaze wax release on the gantry to make sure it just fills the gap and does not stick to the gantry extrusion itself. Not this works REALLY well!

After making sure it is level, I let it cure.

in a Dan Gilbart video I recently learned to make figure 8 motions when doing this. I tried it out and noticed it worked well. I did not actually check it on the surface plate but you notice that the surface is quite flat. Within >=0.0x mm I would estimate. Good enough for this part.

Mirror Glaze

Mirror Glaze Wax release; 16$

Aliexpress.com

Fixing the electronics

I decided to rewire the electronics from scratch. It worked out quite well I must say!

After I wired most of it on the desk I hung it on the wall and started connecting it to the CNC.

Finishing the mechanics

I kinda dropped and messed up the C5 1605 nuts I had on my spindles. As they were already too short anyway I decided to pick up some new ones from Aliexpress:

I was seriously impressed with how riged the DFU version of the ballscrew feels. There is no play at all. I later on measured it on the CNC itself with load and you dont see it budge at all. I can really recommend these C5 1605 DFU screws from Yixindianqi Store on Aliexpress.

So after completing most of the electronics, I went off to mount the spindle and servo motors. Initially, I had put the MAKITA RT0700 router on there; but that died very quickly after a little accident when I crashed it into the toolsetter.

Because the design of my frame is more of an afterthought … I had to add some way to mount the fixture table/wasteboard on the CNC. While it is not ideal to weld on a relatively precise machine frame, it was still the easiest method to do it.

After completing this stage I mounted 36mm of MDF plate to it and went on to the next step

Many small steps in between

So as it goes in a project. you lose focus on documenting a bit and do all kind of small steps. During this time I got probe basic working well on the CNC, tuned the servos and did some final adjustments on the mechanics.

Tramming and aliging the axis

So as in any precision machine build where your mechanics are to perfect, you are going to have to adjust the tram and yaw of the spindle.

I started first with fixing the “nod” of the spindle by putting in a 10mm endmill upside down and using an indicator to make sure the measured distance stayed the same while moving the Z-axis up and down. This was relatively quick to be fixed.

For the trimming (rotation of Z spindle ) I did the following:

So I 3d printed a spacer so I could mount my indicator on the spindle. Turned it round to make sure the distance of the indicated stayed the same. As my z-axis is quite heavy, I found the use of a strap quite useful to slowly get it in the right spot.

Making chips!

After spending some more time with the machine I made another short video where I did some more drilling and milling

Can it mill hardened steel?

So a question that comes up quite a lot is if the Lusintun BT30 ATC spindle can mill steel? The answer is yes, the spindle itself is not the limit. The stiffness of the machine is.

I did some testing on some hardened steel to make sure it could handle normal steel with ease.

Conclusion – Mightymill build Part #4

Since part #3 quite a lot has happened. The machine is together, is working and performing pretty well. As this is the first full CNC build that I have done there are plenty of areas that need improvement. One of the main things is to make the Z-Axis stiffer and make a better connection from the gantry to the ballscrew.

Other than that I’m happy with how it performs!

Make sure to subscribe to the newsletter to make sure you don’t miss any updates.

Feel free to reach out to me on discord

My build has finally begun and in this post I will take you on the building journey. Make sure you have read part 1 here and part 2 here .

Assembling the machine frame

It took a while, but finally I was able to move the machine frame in my recently cleaned shed and get it assembled. For me, the concrete filled machine frame was one of the most time consuming aspects of this build.

The leg assembly was the most difficult to move. While I had put GD-60S wheels under it, it is till a top heavy assembly which weighs 120kg. With a bit of sweat and hurt, I was able to position it and get the assembly going.

I was able to assemble it without too much hassle. To get it all square I had to use the Farmer’s jack to pull the legs inward as there was a slight misalignment. After that it is square (diagonal measurement) within 1-2 mm over a span of 1.6 meters. Which is fine for this application.

It all seems to fit pretty well. Time to go on to the next step.

Lets “rise” up!

It was time to make the riser plates. I used my old and not so trusted HBM BF25 manual mill for this. It actually had lots of troubles during this process. Wobbliness … (DC) motor brushed dying, and other fun electronics issues… But i got it going again and was able to finish the job.

As you can see in the image, the side finish of my milling does not look very good. As I mentioned before my HBM bf25 is quite wobbly and not in a good state. There is still quite some play in the column and in the gibs even after tuning.

As the side surface is not a critical one for my application it is not too bad.

in a Dan Gilbart video I recently learned to make figure 8 motions when doing this. I tried it out and noticed it worked well. I did not actually check it on the surface plate but you notice that the surface is quite flat. Within >=0.0x mm I would estimate. Good enough for this part.

Whetstone set

This set of whetstones was affordable at 25$ and I was able to get it locally quickly.

Aliexpress.com

It all fit well without too many issues. With such precision applications be sure to torque bolts and screws correctly. It is essential that you do in precision applications to ensure equal load and proper contact between surfaces.

After this I also ran the whetstones over it quickly to remove all the burrs.

In addition to this I had to buy the following items:

I used some 3mm thick ground steel parallels for equal spacing vs the alu block.

I used this method to ensure that the side of the extrusions meet the adapter plate perfectly at the same reference plane.

Finally! it is starting to look like a CNC!

Conclusion – Mightymill build Part #3

Moving and re-assembling the machine frame was one of my biggest hurdles. But once I got going it went relatively smooth. The Farmer Jack’s helped a lot with this.

I ordered some new goodies such as Delta ASDA-M controller, 400W ECMA 20b optical encoder ac servo motors. A 1 meter 000 grade granite parallel (all surfaces) and some nice steel AC servo motor mounts. It is now all on the train from China. Hoping for it to arrive at the beginning of December.

The next step will be making the adapters for the ball screws and motors, mounting the extrusions to the table and making the z-axis adapter so it can all be mounted together.

Stay Tuned!

Make sure to subscribe to the newsletter to make sure you don’t miss any updates.

Feel free to reach out to me on discord